What'd you do to your accord today?
- Thread starter HondaLuver83
- Start date
uhhkilleez
Well-Known Member
You should do it but paint it red.
And redhouse.
This is all I got done today..
Dang that looks sick. Very tempted to do that to mine but with either black or red but I don't want to tear apart my headlights so soon.
LowerMyCG5
Well-Known Member
put the wheels back on. new exhast scrapes everywhere. i need to put a flex pipe back on and re make the hangers
then the nut on my morimoto seized up AGAIN -___-
if anyone orders them, ask for the older locking ring. the hex nut is garbage. now i have to cut it off and hope i can find one that fits
then the nut on my morimoto seized up AGAIN -___-
if anyone orders them, ask for the older locking ring. the hex nut is garbage. now i have to cut it off and hope i can find one that fits
Mikey
Well-Known Member
Looks good buddy. Rear needs to come down a bit...?She got a wash and got a photoshoot
Oil pan...?no front bumper on....waiting patiently to be towed away
Dukebb23
Duke Blue Devils
^ Thanks Mikey I think it's just on that slope and it was going towards the water more...
I am actually very happy with the ride quality on this setup though. Almost Oem feeling..but a lot more stiffer and more stable though.
I am actually very happy with the ride quality on this setup though. Almost Oem feeling..but a lot more stiffer and more stable though.
I installed my Eibach rear sway bar with one of the mechanics from my work. Defiantly makes it easier when the car is on a lift. Took about 30 minutes. Felt the improvement almost immediately. Couldn't really test it fully though cause it started raining. Also installed my Acura TL strut bar.
I wish I didn't have to get the extra adapter for 3423 bracket. I wonder why coupes didn't come with 3157 like sedans'.
That's just stupid imo.
↑
↑
Made me want to paint the H and O.
Tiny rubber caps to cover the factory T5 bulbs.
Fits like a condom lol.
For some reasons I thought most of the bulbs for the gage cluster were T5, so I had to dig down my room for some old 168's. Be prepared to see some hotspots~♪
T5 colored caps were direct-fit for the trip odometer and the entire CC unit IIRC. Clock, moon roof, TCS & cruise control buttons were thinner and shorter than T5's, so I had to trim the caps to make them fit at the socket. I knew that ones for the stereo were tiny and soldered, so I had to utilize those trimmed remainings w/ some clear tapes on top.
↑
↑
Obviously, some hotspots on the meters are clearly visible by those outdated 168's, and it's not the greatest for sure. ← (Perhaps it's inevitable regardless of which LED's to work with unless I mod the cluster like Richard's.) Well, I think of it as a practice to remove the gage cluster for the first time. And, it was a good opportunity to clean the +10-year-old accumulated dusts inside the console.
I think I'll convert them to white LED's when I get tired of these.Oh, I also encounterd an SSM CG2.
SykVSyx
Well-Known Member
Like that.
@Duke, car is looking good with those wheels. Give you until late summer to post that now you want full coils.
Last edited:
Dukebb23
Duke Blue Devils
Like that.
@Duke, car is looking good with those wheels. Give you until late summer to post that now you want full coils.
Me too I actually bought the gray carbon fiber insert this morning since I over painted my H on the wheel.
I don't want full coils man. I am very happy with the way she turned out. Any lower and I would be hurting to get in and out of the car with my bad back. Plus I am 6'1 and it wouldn't be good for me. But we shall see later on...just don't tell the wife I said that.
