Go Back   6th Gen Accord DIY and Performance Forums

Register to remove these ads


6th Gen Accord DIY and Performance Forums

6th Gen Accord DIY and Performance Forums (http://www.6thgenaccord.com/forums/index.php)
-   DIY - Do It Yourself Forum (http://www.6thgenaccord.com/forums/forumdisplay.php?f=20)
-   -   Full DIY 01-03 JDM civic fog lights install (http://www.6thgenaccord.com/forums/showthread.php?t=18938)

juicebox00 01-20-2009 01:15 AM

Full DIY 01-03 JDM civic fog lights install
 
Ok, so basically this is the entire process that I did to install the civic fogs. This is what the final product looks like.
http://i40.photobucket.com/albums/e2...P1010096-1.jpg
http://i40.photobucket.com/albums/e2...d/P1010098.jpg
http://i40.photobucket.com/albums/e2...P1010123-1.jpg
http://i40.photobucket.com/albums/e2...P1010131-1.jpg
This is the basic diagram for this set up.
http://i40.photobucket.com/albums/e2...ing2_008-1.jpg

Everyone installs the fog lights there own way onto the bumper. Personally i cut out the end of the inside of the bumper and used L brackets and a screw through the bottom of the bumper to hold the fogs on.
http://i40.photobucket.com/albums/e2...0118091704.jpg

So basically after that you start out with this harness (pic by younglemon)
http://i40.photobucket.com/albums/e2...nking2_008.jpg
First, after installing the fogs on the bumper and plugging them in to "A" and "B"(personally i had the wire the other way around), you want to find ground points for the two ground wires on that section. next i ran the wire of "D-F" up through the engine bay by means of where the intake is (on the v6 model)
http://i40.photobucket.com/albums/e2...0118092050.jpg
Then i ran wire "D-F" on the "F" side through the firewall since "D" will be connecting to "C". There is a point in the firewall that is very good for this specifically shown here.
http://i40.photobucket.com/albums/e2...12081947-1.jpg
In order to use this hole you need to pop out a cap that looks like this
http://i40.photobucket.com/albums/e2...118092014a.jpg
And to pop it out you need to push is with something like a screwdriver from the inside of the car. It is located slightly to the right of the steering wheel column underneath the dash. There is a little pre-cut hole in the firewall padding on the inside that you pull away to get to the tab. To get to this area you need to lay down by the pedals and look up.

Once you feed the "F" side of wire "D-F" through you pull it down and it will look like this.

You might have trouble feeding "F" through the hole because there could be 2 plugs on the end of "F". Find out which plug is connected to "E" and you can cut that off. Double check to make sure you're cutting the right wire though.
http://i40.photobucket.com/albums/e2...18091742-1.jpg

Once you've done this you're now on the last section of wire. This is where you need to do a little bit of splicing. What you need to do is connect the two wires highlighted.
http://i40.photobucket.com/albums/e2...ing2_008-2.jpg
http://i40.photobucket.com/albums/e2...118092052a.jpg

In order to do the next couple of steps you need to take off the button section and to do this you need to pull out the coin tray and unscrew the 4 screws located there. Once the four screws are out all you have to do is pull out the entire section including the air vent. It made be a little stern but it'll come out.
http://i40.photobucket.com/albums/e2...118092053a.jpg

Now where to plug in the last wire section. "F" is going to connect to "G" and "K" will be connected to the fuse box under the steering column. This is exactly what "K" connects to. You probably want to connect it to the bottom left slot (I only suggest here if you have an aftermarket radio thought) which is also works on the same power as the radio so if you can turn the radio on you can turn the fogs on. And by plugging it in the bottom left slot you may blow a "7.5" fuse (if you have a factory radio) that will make your radio not work but it is only the acc. fuse located in drivers side fuse box. So you'll just want to replace that fuse with a "10" fuse. do not use the bottom right! And the upper right area is on the same power as the ambers so you can only turn you fogs on when your ambers are on and when plugging it in there you will most likely blow the fuse for the ambers which is a "10" fuse located in the passenger side fuse box. To avoid it blowing you want to replace it with at least a "15" fuse and nothing more. Put higher fuses in at your own risk though because you aren't usually supposed to replace fuses with more powerful ones, but a slightly higher one should be fine. Upper left is unknown at this point. Also, when you connect it you want to put it up side down compared to how you think you would connect it.
http://i40.photobucket.com/albums/e2...20091455-2.jpg
http://i40.photobucket.com/albums/e2...0091456a-1.jpg

You also want to ground the ground wire on this section of the wire and where i grounded it was on the steering column as shown here
http://i40.photobucket.com/albums/e2...18092013-1.jpg

"H" is where you connect the relay which should come with the fog lights. You'll then pull "I" and "H" up through the wires to where the button area is.
http://i40.photobucket.com/albums/e2...18092014-1.jpg

All that is left is to plug the button into "I' after feeding "I" through the hole in the button panel and close it up as well a putting the bumper back on and checking that all the connections are good.

Another thing you may want to do is drill holes into the bottom of the bumper so that you can use a screw driver to adjust the fog lights once the bumper is on the car.
http://i40.photobucket.com/albums/e2...s/P1010133.jpg
http://i40.photobucket.com/albums/e2...P1010126-1.jpg
You won't need to plug "J" into anything as well as "E" which will also have another part that comes out by "F".

And if you have an OEM fog light switch that you want to use instead of the civic switch use this set up by Russianred
http://www.6thgenaccord.com/forums/s...ad.php?t=17016

I deserve rep points for this epic write up, plz.

Dtownz Thrillah 01-20-2009 03:10 AM

Re: Juicebox's full DIY 01-03 civic fog install
 
It would be epic without blurry pictures, a diagram and no MS paint =]

CG6Lemon 01-20-2009 02:17 PM

Re: Juicebox's full DIY 01-03 civic fog install
 
lol gratz on a write up. rep points for joo son :haysm9:

juicebox00 01-20-2009 02:47 PM

Re: Juicebox's full DIY 01-03 civic fog install
 
Quote:

Originally Posted by Dtownz Thrillah (Post 313709)
It would be epic without blurry pictures, a diagram and no MS paint =]

I'll take new pics with a real camera, the paint is to show the exact thing i was showing. And i think i'll just edit a copy of lemon's pic as a full diagram even though it is self explainatory if you read the text

olivesomra 01-20-2009 04:47 PM

Re: Juicebox's full DIY 01-03 civic fog install
 
Also a diy on NOT using a fog switch. Just a connection to the secondary lighting. If possible.

juicebox00 01-20-2009 05:18 PM

Re: Juicebox's full DIY 01-03 civic fog install
 
Quote:

Originally Posted by olivesomra (Post 313965)
Also a diy on NOT using a fog switch. Just a connection to the secondary lighting. If possible.

I think all you do to do that is splice the "D-F" wire with one of the turn signal lights or the lower amber light. Don't take my word for it since i didn't do the set up that way. So I don't necessarily want to put that on my DIY. If someone can post a set up for doing it that way i'll post it up.

Russianred 01-20-2009 05:38 PM

Re: Juicebox's full DIY 01-03 civic fog install
 
Quote:

Originally Posted by olivesomra (Post 313965)
Also a diy on NOT using a fog switch. Just a connection to the secondary lighting. If possible.

Why the fk would you want to do that? :lolhitting:

I could never understand that.. just do it right, it's not hard. One day you will want to turn the fogs off and won't be able to, or you'll get pulled over by an asshole cop, questioning your foglight use in regular weather. It's happened.

Just connect them the right way. For the awkward position you need to bend in to feed the wire, it's worth it.


Good job JuiceBox! Finally a wiring schematic for the infamous civic fogs!

Rep for you.

:peace:

juicebox00 01-20-2009 05:52 PM

Re: Juicebox's full DIY 01-03 civic fog install
 
Quote:

Originally Posted by Russianred (Post 313999)

Good job JuiceBox! Finally a wiring schematic for the infamous civic fogs!
Rep for you.

If anyone wants to wire a OEM fog switch to their civic fogs, my writeup is found here:
http://www.6thgenaccord.com/forums/s...ad.php?t=17016


:peace:

Thank you, and i put your link to the oem switch on my post

henreeezy xp 01-20-2009 06:35 PM

Re: Juicebox's full DIY 01-03 civic fog install
 
can you be more specific on the part where you started splicing and plugged that wire to the fuse box? and did you splice anything to the turn signals or anything like that?

juicebox00 01-20-2009 06:56 PM

Re: Juicebox's full DIY 01-03 civic fog install
 
Quote:

Originally Posted by henreeezy xp (Post 314059)
can you be more specific on the part where you started splicing and plugged that wire to the fuse box? and did you splice anything to the turn signals or anything like that?

All i did was splice the two wires shown together, I did not touch any wires that were already in the car such as the turn signals. i will be putting up better pics of the exact location of the fuse box and where to plug in the wire.

*Edit: pics up


All times are GMT -4. The time now is 04:47 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Unless otherwise noted, articles are property of 6thGenAccord.com and should not be used without permission. Website staff assumes no responsibility for user-posted content. By posting on 6thGenAccord.com, you agree to allow staff to reuse your material for promotional and other considerations. This site uses VigLink to automatically affiliate commercial links

» Featured Ride
CHECK OUT THIS WEEK'S FEATURED RIDE!



Powered by vBadvanced CMPS v3.2.3