Post your setup ver. Update ver. Big Ballas

HeadUnit:
Pioneer AVIC N1 (DVD/NAV)
2 GB Ipod

Speakers:
Pioneer 6.5 component (front)
Pioneer 6x9 2-way
Pioneer 6.5 component (kick panels)
Kicker tweeters in dash

Amp:
RF p8002 (2400w)

Subs:
2 12" RF Punch stage 3 (1000w each)

Accessories
Kick Panel Speakers
P3 Platinum +/- battery clamps
RF 1 Farad Digital capacitor
RF 4 gauge wiring
Dynamat extreme
Dynamat lisence plate
Viper 791xv extra LCD remote
DEI Motion detector
DEI glass sensor
DEI back up Battery(not installed...)
DEI Immobilizer bypass for remote start
RF Platinum Fuse Holder

I think I'm going to end up with Alpine Type-X Reference components instead of type-R's....

Headunit:
oem

Speakers:
CDT AUDIO HD 6 1/2 inch components with m6 upgrade

Amplifier:
alpine pdx 2.150

oem xm satellite radio

Headunit: Alpine CDA-9887
Front Stage: Hertz MLK 165
Subwoofer: Hertz ML3000
Subwoofer Amp: Hertz HP 2 (1200x1 @ 4ohms)
Component Amp: Hertz HP 4 (440x2 @ 4 ohms)
Sound deadening: RAAMmat BXT
Power wire: JL Audio 2awg
Interconnects: Stinger Hyper Series 2&4 Channel
Power: Kinetik HC1400, Excessive Amperage 200A H.O. Alternator
Alarm: Clifford RSX 3.5

Every stinger accessory you can think of under the hood that I don't want to waste time listing.

I'll go ahead and take this icon. :roy:

I'd imagine you also have the KTX-100EQ to actually tune the 9887?

hu: alpine dva-9965 with tme-m740bt 7" touchscreen
front components: focal 165v2 with CDT Audio ES-02 tweeters
front components amp: orion-800.2 (200w @ 2ohm)
rear speakers: mb quart rce269 6x9
sub: 2 12" eclipse titanium (3000w @ 1ohm)
sub amp: rockford fosgate t40001BD (4000x1 @ 1ohm)
sound deadening: dynamatt
wires: JL audio & monster cables
power: kinetik hc2400 (2600 amps) in the trunk and optima red top under the hood
alarm/auto starter: compustar 2W900fmr with hood, trunk, and door trigger sensors.

Alpine 9856 Headunit w/ 30gb vid ipod
RF 2 Farad cap
3 10'' JL W1s in flush mounted box
Kenwood 1800 watt amp (need somethin else really)
Polks front and back
Remote start
4 gauge wire

see the subs partially in my sig..

Totalimmortal said:

I'd imagine you also have the KTX-100EQ to actually tune the 9887?

Click to expand...

You can ACTUALLY tune it like a man without IMPRINT. You actually lose all control if you use IMPRINT. I am debating between IMPRINT and the H701 right now but that will be decided when the custom trunk goes in.

Way to be an ashole dude. It was just a question.

Well, here's mine...

Head unit: Pioneer DEH-P5800MP
Dash: Factory tweeters
Front speakers: Pioneer 4-way 6.5s (I forget which model, they are the TS series, though)
Rear Speakers: Pioneer TS-6971R 3-way 6x9s
Amp: Pioneer GM-6200F 600watt 4-channel
Subwoofers: Two Rockford Fosgate Punch P1 10"s
Amp: Rockford Fosgate Punch P600.2 1800watt 2-channel
Box: Custom-built and carpeted by myself and my father to exact specs of RF
Wiring: Scosche everything, 8ga. to the Pioneer 4ga. to the Punch

My weakest link is probably the 6x9s, even with the HPF set to 50hz they still crap out if you crank it. I'm also not very satisfied with the 6.5s, but they are HPF'ed at 80hz, and they do a decent job with the mids and highs, combined with the factory tweeters.