cg3low4life
Active Member
- Joined
- Nov 17, 2015
- Posts
- 30
- Reaction score
- 0
98 accord 4 door
Sent from my Z970 using Tapatalk
Sent from my Z970 using Tapatalk
F20b td94u distributor - need help with wiring
- Thread starter cg3low4life
- Start date
cg3low4life
Active Member
- Joined
- Nov 17, 2015
- Posts
- 30
- Reaction score
- 0
Helppp
Any one? I know people know about this swap
Sent from my Z970 using Tapatalk
Any one? I know people know about this swap
Sent from my Z970 using Tapatalk
james'99
Well-Known Member
Re: Helppp
What swap?
What swap?
RedRyder
Save the manuals
Re: Helppp
Merged with your other thread. If you want help you need to provide people with more information.
Merged with your other thread. If you want help you need to provide people with more information.
Last edited:
cg3low4life
Active Member
- Joined
- Nov 17, 2015
- Posts
- 30
- Reaction score
- 0
cg3low4life
Active Member
- Joined
- Nov 17, 2015
- Posts
- 30
- Reaction score
- 0
Td94u
My harness has only 4 wires and the distributor from the f20b has 8 I was told to get the other 4 wires from the camshaft but I don't know what colors go to what color
Sent from my Z970 using Tapatalk
My harness has only 4 wires and the distributor from the f20b has 8 I was told to get the other 4 wires from the camshaft but I don't know what colors go to what color
Sent from my Z970 using Tapatalk
RedRyder
Save the manuals
Merged again. Please stop making new threads on this topic, you only need update this one.
Jordan_H
Well-Known Member
Did you look through this?
http://www.6thgenaccord.com/forums/showthread.php?t=46696&highlight=H23a+swap
I know it says h23a but it is for instructions on an f20b.
I've heard of people using an h22 dizzy. This should be of some use to you.
ook at the unused plug on the driverside of the engine, up by the end of the fuel rail. The 4 wires there were for the crank sensors your USDM motor had (red, white, green & blue in what looks like a O2 sensor plug). These go color for color to the JDM distributer plug. Your stock (orginial) distributor was a black rectangle 4 wire plug (yellow, yellow/green, black, black/yellow), these go color for color to the JDM distributor. Start the car and enjoy the F20b goodness.
http://www.6thgenaccord.com/forums/showthread.php?t=46696&highlight=H23a+swap
I know it says h23a but it is for instructions on an f20b.
I've heard of people using an h22 dizzy. This should be of some use to you.
ook at the unused plug on the driverside of the engine, up by the end of the fuel rail. The 4 wires there were for the crank sensors your USDM motor had (red, white, green & blue in what looks like a O2 sensor plug). These go color for color to the JDM distributer plug. Your stock (orginial) distributor was a black rectangle 4 wire plug (yellow, yellow/green, black, black/yellow), these go color for color to the JDM distributor. Start the car and enjoy the F20b goodness.
Last edited:
cg3low4life
Active Member
- Joined
- Nov 17, 2015
- Posts
- 30
- Reaction score
- 0
Jordan_H
Well-Known Member
I wish I had not helped you. There is no need for such childish behavior. Welcome to the forum and good-bye, because more than likely you will be banned.
