DIY Clutch Replacement (4 cylinder)

INK DEMON

Well-Known Member
Joined
Nov 29, 2008
Posts
79
Reaction score
10
Location
SAN DIEGO
It was time to do the clutch again so I decided to do a write up. Feel free to let me know if anything is missing.

Things you'll need:
- Wrenches
- Ratchets and sockets (1/4, 3/8 and 1/2" drives are all useful)
- Breaker bar(s)
- Torque Wrenches
- Jack
- Jack Stands
- Crankshaft pulley tool
- Chisel or Pickle Fork and Sledge
- Pry Bars
- Rubber or Wood Blocks
- Oil Drain Pan
- Cotter Pins
- Rubber Mallet
- Funnel (with hose attachment will DEF help)
- Wire or twine
- Rags


I also decided to do the crankshaft seal while I was in there so I decided to include the steps for the oil change as well. Each picture includes the torque specs to the bolts/nuts.

1. Raise the car from the lift point on the sub-frame.
IMG_2070_zps1njx5xo6.jpg

2. Place jack stands under pinch rails.
IMG_2071_zpscufmlsty.jpg

3. Drain oil. Install new washer and reinstall drain plug.
IMG_2077_zpse6ismohe.jpg

4. Remove oil filter. Coat gasket on new filter with oil and reinstall.
IMG_2080_zps0y7oaung.jpg

5. Remove intake.
IMG_2082_zpsogylyi9n.jpg

6. Remove battery.
IMG_2083_zpsyjytyhg5.jpg

7. Remove battery tray. There is one bolt under the tray in this picture.
IMG_2088_zpsfnlrkvep.jpg

This is the bolt which is out of view in previous picture.
IMG_2090_zpsgxs65kwo.jpg

8. Remove harness clamp and clutch line clamp.
IMG_2093_zpsmpypljrq.jpg

9. Remove clutch slave cylinder.
IMG_2096_zpsssecnfj8.jpg

10. Remove transmission ground cable and starter cable clamp.
IMG_2098_zpsoazw6xqz.jpg

11. Remove starter cable and starter mounting bolts. Then remove starter. There is one cable (out of view) which just plugs in behind the starter cable.
IMG_2100_zps4kpvoynb.jpg

12. Disconnect back-up light connectors and unclip the wire harness.
IMG_2104_zpsl3l04nhg.jpg

13. Remove shift cable bracket. One bolt is not visible in picture.
IMG_2106_zpskzj3mzwt.jpg

14. Remove cotter pins and disconnect the shift cables.
IMG_2108_zpsw9ig6xy5.jpg

15. Disconnect vehicle speed sensor and remove rear engine mount bracket.
IMG_2112_zpsir73ivay.jpg

16. Remove both upper transmission bolts.
IMG_2115_zpsmvh6wyfu.jpg

17. Raise car slightly and slide a jack stand WITH rubber block under oil pan. IT IS VERY IMPORTANT TO USE A RUBBER OR WOOD BLOCK. The weight should be very slight on the jack stand.
IMG_2118_zpsrxewpmio.jpg

18. Unclip the A/F sensor harness from bracket and remove front engine mount bolts.
IMG_2121_zpsfujfkdgr.jpg

19. Remove splash shield.
IMG_2119_zpsnupvtzdo.jpg

20. Remove cotter pins and castle nuts. Loosen bolts on damper forks.
IMG_2123_zps4a2xcbg6.jpg

21. Use chisel or pickle fork to separate ball joints from lower arms. Be careful not to damage ball joints.
IMG_2126_zps3eqliq0b.jpg

22. Loosen drain bolt on transmission and drain transmission fluid. Once drained, install new washer and reinstall drain plug.
IMG_2129_zpsgl92aqfm.jpg

23. Pry out axles from transmission and from intermediate shaft. Use the wire/twine to hang ends of axles in the air. Cover ends with rags.
IMG_2131_zpsviyedv6u.jpg

24. Remove intermediate shaft.
IMG_2130_zps5vrwpn3y.jpg

25. Remove engine stiffener.
IMG_2136_zpso7dwkewd.jpg

26. Remove intake manifold bracket.
IMG_2132_zpsq0qmg3ql.jpg

27. Remove radius rod bolts from lower arm. (Not pictured) The radius rods come out from the sub-frame and connect to lower arms. 2 bolts on each arm. Torque Specs: 119 ft-lbs
28. Unclip power steering line from sub-frame. There are two clips, there is one towards the front of the car as well as the one pictured.
IMG_2142_zps1pd9xycp.jpg

29. Make reference marks on sub-frame rear beam. Then remove three bolts on each side.
IMG_2138_zpsuogntbfs.jpg

30. Remove front sub-frame bolts. Carefully lower sub-frame and move it out of the way.
IMG_2144_zpsh8rpcuz8.jpg

31. Remove nuts on transmission mounting bracket.
IMG_2147_zpsmktdfwng.jpg

32. Remove transmission mount bolts and remove mount.
IMG_2146_zpsxnrlryio.jpg

33. Remove rear engine mount bracket mounting bolts. One is out of view in this picture.
IMG_2133_zpsj7aefjry.jpg

This is the third bolt which is out of view in previous picture.
IMG_2158_zpsvpymwhky.jpg

34. Remove front transmission mounting bolt.
IMG_2156_zpsojkxzj6f.jpg

35. CAREFULLY pull transmission away from the engine while supporting transmission with jack. Once the shaft is fully out, carefully lower transmission and pull away from car. (Not pictured)
36. Remove bolts holding pressure place onto flywheel. Remove pressure plate and clutch. Pressure Plate Torque Specs: 19 ft-lbs. (Not pictured) When tightening pressure plate, tighten bolts in crisscross pattern in small movements.
37. Install crankshaft pulley tool and hold crankshaft while removing flywheel bolts.
IMG_2164_zpskukwdqu7.jpg

38. Remove flywheel bolts, and remove flywheel. When installing flywheel, tighten bolts in crisscross pattern.
IMG_2168_zpsynl15ixy.jpg

39. Get flywheel resurfaced. (Not pictured)
40. This is the crankshaft seal. Remove the housing and replace seal. When reinstalling, apply honda-bond on mating surface and on the tip of mounting bolts and reinstall. Mounting Bolts Torque Specs: 104 in-lbs.
IMG_2165_zpszqc2jcsk.jpg

41. Reinstall flywheel.
42. Use clutch alignment tool to hold clutch in place.
IMG_2171_zpseki5fmr5.jpg

43. Install new pressure plate.
44. Apply urea grease to release bearing guide, shaft splines and release fork.
IMG_2173_zpsubqnmuh3.jpg

45. Apply urea grease to pivot point on release fork.
IMG_2174_zpsmhiobeql.jpg


Installation is reverse of removal.
Once everything has been installed. Fill transmission through fill hole until fluid starts to run out (approx. 1.9 qts)
Refill engine oil (approx. 4.5 qts)
 
Last edited:

Varnell

Well-Known Member
Joined
Mar 16, 2013
Posts
1,102
Reaction score
4
Location
Charlotte, NC
Impressive DIY write up! I'm sure plenty of people will appreciate and make use of this thread. Definitely a DIY you really need to ask yourself if you're capable of COMPLETING, before starting.
 

CG6Lemon

Detailing Enthusiast
Joined
Jun 6, 2008
Posts
7,715
Reaction score
45
Location
S.F Bay Area, CA
Thanks for taking the time to grab pics for each step, marking the numerical order from start to finish, including tq specs for each bolt. This type of write up requires a lot of time and effort to put together. Been on this board for a while and it's been a while since I've seen quality write ups. Refreshing to see and read that people still enjoy working/tinkering with their accords. :thumbsup:
 

RedRyder

Save the manuals
Joined
Sep 5, 2008
Posts
19,516
Reaction score
116
Location
Fawking, OH
Thanks for taking the time to grab pics for each step, marking the numerical order from start to finish, including tq specs for each bolt. This type of write up requires a lot of time and effort to put together. Been on this board for a while and it's been a while since I've seen quality write ups. Refreshing to see and read that people still enjoy working/tinkering with their accords. :thumbsup:

Exactly what I was thinking. Thank you for a quality contribution! Repped and added to master list.

It may be a good idea to add the tightening order for the flywheel bolts, or if unavailable maybe mention to tighten in star pattern.
 
Last edited:
Back
Top