PSYCO G 305
Well-Known Member
Does anybody know how to program another remote for the factory keyless entery or "arlam system"??????? I just got another one and I want to program it without going to the dealer and spending alot of money!
keyless Entery
- Thread starter PSYCO G 305
- Start date
i think if you have a 91-00 you can do this :
Storing transmitter codes:
The codes of up to three transmitters can be read into the keyless receiver unit memory. (If a fourth code is stored, the code which was input first will be erased.)
NOTE: It is important to maintain the time limits between the steps.
Turn the ignition switch ON (II).
Within 1 to 4 sec. , push the transmitter lock or unlock button with the transmitter aimed at the receive (control unit).
Within 1 to 4 sec. , turn the ignition switch OFF .
Within 1 to 4 sec. , turn the ignition switch ON (II).
Within 1 to 4 sec. , push the transmitter lock or unlock button with the transmitter aimed at the receiver (control unit).
Within 1 to 4 sec. , turn the ignition switch OFF .
Within 4 sec. , turn the ignition switch ON (II).
Within 1 to 4 sec. , push the transmitter lock or unlock button with the transmitter aimed at the receiver (control unit).
Within 1 to 4 sec. , turn the ignition switch OFF .
Within 4 sec. , turn the ignition switch ON (II).
Within 1 to 4 sec. , push the transmitter lock or unlock button with the transmitter aimed at the receiver (control unit).
Confirm you can hear the sound of the door lock actuators. Within 1 to 4 sec. , push the transmitter lock or unlock button again.
Within 15 sec. , aim the transmitters (up to three) whose codes you want to store at the receiver, and press the transmitter lock or unlock buttons. Confirm that you can hear the sound of the door lock actuators after each transmitter code is stored.
Turn the ignition switch OFF , and pull out the key.
Confirm proper operation with the new codes(s).
hope this helps.
Storing transmitter codes:
The codes of up to three transmitters can be read into the keyless receiver unit memory. (If a fourth code is stored, the code which was input first will be erased.)
NOTE: It is important to maintain the time limits between the steps.
Turn the ignition switch ON (II).
Within 1 to 4 sec. , push the transmitter lock or unlock button with the transmitter aimed at the receive (control unit).
Within 1 to 4 sec. , turn the ignition switch OFF .
Within 1 to 4 sec. , turn the ignition switch ON (II).
Within 1 to 4 sec. , push the transmitter lock or unlock button with the transmitter aimed at the receiver (control unit).
Within 1 to 4 sec. , turn the ignition switch OFF .
Within 4 sec. , turn the ignition switch ON (II).
Within 1 to 4 sec. , push the transmitter lock or unlock button with the transmitter aimed at the receiver (control unit).
Within 1 to 4 sec. , turn the ignition switch OFF .
Within 4 sec. , turn the ignition switch ON (II).
Within 1 to 4 sec. , push the transmitter lock or unlock button with the transmitter aimed at the receiver (control unit).
Confirm you can hear the sound of the door lock actuators. Within 1 to 4 sec. , push the transmitter lock or unlock button again.
Within 15 sec. , aim the transmitters (up to three) whose codes you want to store at the receiver, and press the transmitter lock or unlock buttons. Confirm that you can hear the sound of the door lock actuators after each transmitter code is stored.
Turn the ignition switch OFF , and pull out the key.
Confirm proper operation with the new codes(s).
hope this helps.
yup sounds about rite... heres some links if u need additional help:
http://www.handa-accessories.com/crv/KEYLESSPROG.pdf
http://www.honda-acura.net/forums/showthread.php?t=202634&highlight=keyless+entry
http://www.handa-accessories.com/crv/KEYLESSPROG.pdf
http://www.honda-acura.net/forums/showthread.php?t=202634&highlight=keyless+entry
