Recent content by tdoggs01v6

  1. T

    no power after 6spd swap

    Got the car running. Check engine light does not come on, but I have four codes. The codes I am getting are P0452, P0450, P0505, and P0170. The first two are the evaporative emission stuff, which I don't really have hooked up/deleted. P0505 is the idle air control, not sure why this is bad. The...
  2. T

    no power after 6spd swap

    I was actually just reading through your swap thread for that. Would the clutch switch hold the car back from cranking?
  3. T

    no power after 6spd swap

    Thanks RedRyder. But I think I am figuring it out. I got another ECM and repaired the other one. I think what is holding me out now is just the Clutch Switch and figuring out the immobilizer.
  4. T

    no power after 6spd swap

    The resistor that comes from pin out 4 on the CL connector is blown. Not sure if this happened from the previous owner or if my wiring would have caused it. I double checked my wiring, I have Accord wire 18 in the 4 spot, both MIL wires. I don't see any issues with the wire shorting out some...
  5. T

    no power after 6spd swap

    does anyone know where to find resistors charts for the ECM. It looks like there is once resistor inside the ECM that looks shorted. Wondering what the value of the resistor is to perhaps replace.
  6. T

    WTB 03 CL-S Manual ECU

    Looking for a 03 Acura CL type s manual ECU 37820-PGE-A11 or 37820-PGE-A12. Need it to finish my swap, the one I have does not seem to be working.
  7. T

    FS: Projectors and 6 Speed Parts

    ECU still for sale?
  8. T

    no power after 6spd swap

    So I unplugged the Immobilizer at the ignition. I ended receiving a code from the ECM. P1607, which is a ECM/PCM internal circuit failure. Is there any way to test the ECM for issues or am I going to have to find another ECM?
  9. T

    no power after 6spd swap

    thanks for posting the picture
  10. T

    no power after 6spd swap

    Hello everyone. I am at the end of my 6MT swap and I am having some power issues. For a run down on what I have since my build thread has not been updated. I have an 2001 V6 EX and I am running an 03 Odyssey motor with a 03 CL-S 6MT engine harness, transmission, and ECU. I have the third ECU...
  11. T

    WTB: mods close

    mods please close.
  12. T

    tdoggs J35 6MT build

    After going through my boxes of parts I had discovered that I did not have an engine harness. So I ordered a 03 manual Cl-s engine harness. Thinking that it would make my swap easier. The ECU that I purchased at the same time as the manual transmission and car harnesses, turned out to be for an...
  13. T

    tdoggs 01 sedan bagged out

    Thanks. The fuel door is actually wrapped. The roof and fuel door are wrapped in a 3D Carbon Fiber print wrap. It looks so close to the real thing it is unbelievable.
  14. T

    tdoggs 01 sedan bagged out

    Thanks man, we haven't been doing shows lately. Take a lot of work and stress to get things organized, as a group we decided to stop. But we are always going to shows. We are just a group of friends, that have been going to shows for a while. You are always welcome to ride down with the group to...
  15. T

    tdoggs J35 6MT build

    Thanks for the responses WHEELMAN. I will see what I can figure out on the immobilizer.
See more

Latest posts

Random media

GEDC0357
3K53F73N15If5Ld5K6d5v9798d90459b71477
IMAG0080
image
Web6
Back
Top