Search results

  1. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Ticking sound was due to excessive piston to valve clearance. Project was success in a way that I learned a lot about engine building and different ways to achieve a target. Currently I have a h23a running in my car. So this year, I will redo the g23, lower compression and probably go with turbo.
  2. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    So I finally saved some money to buy a hondata ecu(black ecu from kstuned). The ticking sound in the cylinder head valve train is still there.
  3. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    8mm metric.
  4. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    https://youtu.be/TcJQPcq_TIQ So I started the engine with stock jdm ecu. Does anyone know the cause for this sound?
  5. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Compression test results(before valve adjustment): 1,2,3,4 = 225psi, 235 psi, 255psi, 255 psi
  6. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Torqued the head bolts to 80 ft lbs. Installed the timing belt.
  7. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Cylinder head placed on the block. Left front blocked oil passage. Right front blocked oil passage. Middle gasket area. View of blocked passages from the top of the engine.
  8. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Placing the f23a gasket on the cylinder head. Rear holes line up perfect but the front get's cut off earlier but its fine. H22a gasket will leave a small portion unblocked as was posted earlier in the thread.
  9. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Ordered two pins from ebay for blocking the oil passages on the front of the engine. No need to install plug or mess with the cylinder head. Installed with lot of lube and patience.
  10. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Installed f23a head gasket. Better than h22a head gasket at covering oil holes in the block and fits the cylinder chamber perfectly.
  11. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Re: Projekt G23[Hold] | [Current] Euro r H22A Time to pull the engine out again and see what went wrong. Should be ready to come out this week.
  12. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Re: Projekt G23[Hold] | [Current] Euro r H22A The other day saw the temp gauge climbing while sitting in traffic. Pulled over confirmed fans were running. Temperature came down but as soon as pressed on throttle it started heating up again. Also I can hear pinging sound only under load.
  13. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Re: Projekt G23[Hold] | [Current] Euro r H22A Decided to fix the clutch pedal flex issue. Removed the dash, bent a metal strip 90°, drilled a slot for adjustment and finally used a hose clamp to secure it to the metal tube.
  14. T

    Bense's H23A Swap HowTo & Discussion Thread.

    JDM PCD ecm does not monitor catalytic converter efficiency i.e. it does not monitor second oxygen sensor at the end of the catalytic converter. This ecm is NOT california emission legal.
  15. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Re: Projekt G23[Hold] | [Current] Euro r H22A Thanks. Yes will have to be careful in the rain. You cannot install bypass valve on aem V2 intake. That's the only downfall.
  16. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Re: Projekt G23[Hold] | [Current] Euro r H22A Ordered apexii WS2 exhaust online $655. Fedex delivered at wrong address :snoopfacepalm: Waiting on seller to file claim so they can ship another one. Meantime I am going to pull out the dash panel to fix the upper arm of the clutch pedal bracket.
  17. T

    Need advice on engine replacement

    Search the forums, there is wealth of information on that, Correct me if I am wrong but euro r is sub version of h22. Never heard of euro h23. If you can get jdm h23a with automatic you would have to use the ecm that came along with it.
  18. T

    Need advice on engine replacement

    euro obd2 has no immobilizer. sn: xxxxx-pcd-xxx
  19. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Re: Projekt G23[Hold] | [Current] Euro r H22A Finally the panda is here :)
  20. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Re: Projekt G23[Hold] | [Current] Euro r H22A Installed AEM 24-6015C Gun Metal V2 Induction System $324 tax inclusive from amazon.
  21. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Re: Projekt G23[Hold] | [Current] Euro r H22A I can confirm that euro r ecm xxxxx-pcd-004 does not require EPS(electronic power steering) signal if the power steering pressure switch is connected to the ecm. It will mirror EPS high and low signals and raise the idle based on our current...
  22. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Re: Projekt G23[Hold] | [Current] Euro r H22A Installed a used H22 power steering pump, new bracket on the engine. Got the hose shop to weld two JIC/AN -6 fittings, one on the pump side and the other just before the pressure switch. I still don't know if the ecm will sense this pressure switch...
  23. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Re: Projekt G23[Hold] | [Current] Euro r H22A Installed ATI H22 street damper part #918468, $387 ebay. Could not get the bolt out from the pulley with the pulley removal tool oem #27176. Broke the breaker bar first and then a 1/2 in extension. Went to home depot, got the $129 8 gallon 125psi...
  24. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Re: Projekt G23[Hold] | [Current] Euro r H22A Finally made my radiator stays from 2 angle iron pieces. Drilled one side with a hole for rubber grommet. Other sides are slots for depth and distance adjustment. Crude but sturdy. V1 has to be ugly :)
  25. T

    Projekt G23[Rebooted] | [Ended] Euro r H22A

    Re: Projekt G23[Hold] | [Current] Euro r H22A Bolted down my radiator support. Did use lock nuts overs thread lock.

Latest posts

Random media

Engine Turbo Sig
Accord V6 as of April 22, 2010
1361482259630
current
IMAG3542
Back
Top