Search results

  1. J

    2002 accord f20b swap questions

    I have the F20B swapped into my 98 sedan. I am running the PCB-004 (I think those are the right numbers) ecu for this engine and I have passed GA emissions testing for last 3 years. First time I was scared ***tless about passing though.
  2. J

    F20B bucks and stalls at stop sign

    Got the car up and running, and emissions tested with JDM ecu. On the way to inspection site, the tranny bumped when I began to stop at sign and then stalled. It took 5 or so cranks to get it started again. It happened again on way back home. When accelerating, it takes a few seconds to engage...
  3. J

    F20B Woes, Help!

    So Dizzy order is off... I went to double check timing at the dizzy because thats the only place I haven't checked. Surprise! I turned crank to TDC and took off the dizzy cap. The rotor is pointing at cylinder 3. How do I fix this? the only thing i can think is that this cam or both are off...
  4. J

    F20B Woes, Help!

    The car is 98 accord, automatic transmission. The ecu was bought on eBay and is 37820-PCA-N64 supposedly from JDM Torneo. I have tried running it on stock accord ecu and that will run it in more or less the same way.I get same issues regardless and no CEL with either. I do have a ticking noise...
  5. J

    F20B Woes, Help!

    Was seriously considering driving my accord off a cliff, the only problem is it doesn't drive, at least not well. Here's the background and the problems. I swapped the f23a1 to JDM F20B. I started the car which idled at 1200 for about 3mins and as the car warmed, the idle gradually fell and...
  6. J

    F20b Knock Sensor Location

    You did, but to clarify, the hole is considerably lower than the oil filter. I should have said can it go anywhere in the block or does it have to be near the placement on the stock motor?
  7. J

    F20b Knock Sensor Location

    I looked back there and didn't see an available port. I am planning to stay obd2. Do you know if I can just tap a hole that is unused that is near the oil pan. Ill try to post a pic when I get home of where the hole currently is.
  8. J

    F20b Knock Sensor Location

    I have almost everything wired in but I cannot find a place for the knock sensor. I don't think the F20B has a knock sensor, but is there I place I can add one from my f23a1?
  9. J

    ECU to run JDM F20B

    So I got an ECU in the mail; definitely not the one I order. I received a 37820-PCA-N64. Does anyone know if this will run my F20B?
  10. J

    ECU to run JDM F20B

    Thanks for the replies. I considered just running the F20b ecu but since it won't read on USDM scanners, I have to find a work around. I read that it is possible to desolder the immobilizer and put in the immobilizer from the f23 ecu. I will probably try the H22a but is it true I have to get H22...
  11. J

    ECU to run JDM F20B

    Thanks for the reply. Even if the dizzy and all other connections are wired correctly to the harness, it will still give misfire codes? Will the same happen if I use the H22 ecu?
  12. J

    ECU to run JDM F20B

    Ok, before you guys rip me to shreds, I couldn't find this specific answer after searching. Considering that JDM obd2 doesn't communicate with USDM obd2, and that the F20B is a destroked H22, is it possible to run my obd2 F20B with an OBD2 USDM H22 ecu? If not, can I run the stock f23 ecu just...
Back
Top