Search results

  1. 6

    oil in spark plug tube

    My buddy had the same problem for him it ended up being a broken oil ring on the piston. I would start with the rubber seal in the spark plug tube
  2. 6

    bad Knock sensor?

    I'm having more issues yet again. I have just done a re ring on my f23a1, following that I was having issues with the idle(idle had been crazy for a while) and basically no power and the Vtec not working i was throwing all kinds of codes for the TDC sensor, MAP sensor, Barometric Pressure...
  3. 6

    high idle and limp mode

    I have changed both the sensors and the car is running perfect thanks for the help guys!
  4. 6

    high idle and limp mode

    Distributor did not help at all i'm still throwing a P1361 code so my next move is replacing the TDC sensor along with the crank sensor
  5. 6

    high idle and limp mode

    okay i cleaned the IACV and it brought the idle down to normal until i start driving then as soon as i start rolling in neutral or clutch pushed in the idle picks back up but when i come to a complete stop it returns to normal. and for the limp mode I've been told the ignition module in the...
  6. 6

    high idle and limp mode

    I have just done a re ring on my F23a1 new piston rings and bearings. now when I crank the car it immediately idles at 2000 rpm and will not drop. however when the rpms hit 3000 the engine cuts out as if it hits the rev limiter which I'm told is the engine in limp mode. I'm throwing 2 code one...
  7. 6

    Cg3 5spd rpm hanging

    P1106***
  8. 6

    Cg3 5spd rpm hanging

    I'm still throwing p11016 for the barometric is it possible that when it runs good the air pressure is right but on days that it's not it's causin my idle to hang?
  9. 6

    Cg3 5spd rpm hanging

    Alright man what do you mean exactly by PID and by any chance would resetting the codes maybe set it back to normal?
  10. 6

    Cg3 5spd rpm hanging

    Yes I ran the obd2 today the codes I got were for the throttle position sensor and the barometric pressure sensor give you any more ideas?
  11. 6

    Cg3 5spd rpm hanging

    Next question the auto parts store said their was a difference in the iacv from automatic to manual which I know is true I was wondering however if that difference comes with the part it's self or if it's in the wiring on the car? Thanks guys
  12. 6

    Cg3 5spd rpm hanging

    Pcv is good it is a new one only been in around a month so I should start looking harder at the iacv
  13. 6

    Cg3 5spd rpm hanging

    The car is starting to get worse now when the idle does drop it almost stalls out completely but will pick up at last second. The other day I drove home and it was fine this just started again. When I first crank the car it idles fine I can rev it in neutral and it drops fine it only stick when...
  14. 6

    Cg3 5spd rpm hanging

    Now the idle varies sometimes on a cold start its normal the 12-1600 range sometimes it revs up to near 3000 I drove the other day and it never hang up or anything it was perfect then all the sudden it just started again
  15. 6

    Cg3 5spd rpm hanging

    The throttle cable is working freely I've already check it I've looked for vacuum leaks. No I'm at a loss of ideas unless it is the idle control valve but due to its high cost I'm still holding out hope
  16. 6

    Cg3 5spd rpm hanging

    Yeah I'll get one in the morning it just hangs for a while then it'll drop but when I first cranked it she idled way to high so I'm thinking idle control sensor the rpm goes up and down a lot after it warms up but it stays between 1200 & 1800 it normally idels we'll under 1000
  17. 6

    Cg3 5spd rpm hanging

    Nah man I'm not using cruise at all
  18. 6

    Cg3 5spd rpm hanging

    Hey so last night on my way home I noticed my rpms hang around 3000 when I push the clutch in it'll hang for a while then drop to normal But it decreases really slow everything is clean and lubed I made sure of that already just wondering if anyone else has ran into this problem with the f23 and...
  19. 6

    2000-20001 front bumper conversion

    Hey guys I want to put an 01 or 02 front bumper clip on my 2000 accord coupe I know it can be done but I was wondering if it required a lot of work or was pretty much a direct fit before I bought a new clip. Thanks guys
  20. 6

    6spd for 4 cylinder

    Yeah I'm almost positive the synchronizer is out you can double clutch it and wait a long time and it'll slide right in gear...
  21. 6

    6spd for 4 cylinder

    Yes I have I'm almost positive the syncronizer is out you can double clutch it and wait a long time and it will slide right into gear..
  22. 6

    6spd for 4 cylinder

    Hey guys I have a 2000 coupe with an f23 V-tec engine it is a 5 spd but 5th has been growling hard since I got it I'm in fear that it's about to go it but I'd love to make it a 6 spd I was wondering if anyone knew of a tranny that would mount up to my engine maybe even if I need a kit any...

Latest posts

Random media

4
DSC 0230
My LEDs
Dash
Cobra R wheels (Winter prep)
Back
Top