2002 Accord V6 need new engine

Discussion in 'Engine & Transmission Mods' started by thenitz, Jan 6, 2018.

  1. thenitz

    thenitz Member

    Posts:
    5
    Likes Received:
    0
    Joined:
    Mar 30, 2014
    Location:
    AZ
  2. 98acclude

    98acclude Well-Known Member

    Age:
    31
    Posts:
    635
    Likes Received:
    0
    Joined:
    Jul 29, 2008
    Location:
    Joplin Missouri
    if I remember right, I dont believe the 6 speed transmissions will bolt up to the j35... I did hear though that you can take the crank and rods n stuff out of the j35 and put them into like a j32... Someone else with more knowledge on the j series should chime in as I've just begun my research into these motors too.
     
  3. datechboss101

    datechboss101 Well-Known Member

    Posts:
    305
    Likes Received:
    1
    Joined:
    Oct 15, 2016
    Location:
    Orlando
    The J35 can be hooked up to a 6MT as the coupe variant (7th-9th gen) has a 6-6 option. You can definitely fit the J35 into your CG1 and you should definitely do a 6MT (even though you have a 9.5GCSi).
     
  4. Rusty Accord

    Rusty Accord Well-Known Member

    Posts:
    434
    Likes Received:
    3
    Joined:
    Feb 27, 2017
    Location:
    USA
    Connie went with a JDM J32 for his 01 coupe. It was a direct swap. I think he's over 300Kkm on it since the conversion, and it's still running strong (he's got over 500Kkm on it now). There also a couple of other J35 swaps on here as well. Might be worth doing a search to see what's involved.
     
  5. Accordx

    Accordx Well-Known Member

    Posts:
    215
    Likes Received:
    2
    Joined:
    Dec 23, 2016
    Location:
    Washington, USA
    Yeah I think the J32 or J35 would be decent options for your situation
     
  6. capsidx

    capsidx Well-Known Member

    Posts:
    473
    Likes Received:
    17
    Joined:
    Aug 21, 2016
    Location:
    Florida
    Dont think we will be seeing any more activity from the OP on this post lol:shrug:
     
  7. thenitz

    thenitz Member

    Posts:
    5
    Likes Received:
    0
    Joined:
    Mar 30, 2014
    Location:
    AZ
    Duplicate
     
    Last edited: Jan 25, 2018
  8. thenitz

    thenitz Member

    Posts:
    5
    Likes Received:
    0
    Joined:
    Mar 30, 2014
    Location:
    AZ
    Sorry been busy working still looking into it oddly I didn't get an email update on this thread. I am going to keep this one as automatic just need to figure out which engine, auto tranny, computers, dashboard etc will all work considering the jump
     
  9. capsidx

    capsidx Well-Known Member

    Posts:
    473
    Likes Received:
    17
    Joined:
    Aug 21, 2016
    Location:
    Florida
    I've done H23a1 and F20b. Both are fairly simple swaps as far as the engine and trans is concerned. Wiring is somewhat complex. H22 is the most expensive but you'll make the most power. I am not a fan of FRM sleeves so I went with the iron sleeved F20b over the H22 after my H23a1 exploded. Those are two options I can say are good based on experience. Well one at least. The V6 is probably more work than you're ready to do.
     
  10. Apzy6

    Apzy6 New Member

    Posts:
    2
    Likes Received:
    0
    Joined:
    May 27, 2018
    Location:
    Toronto
    is it possible to swap in a j35a8 into a 4dr?
     

Share This Page