98 - 02 honda Accord AT Wiring swap into MT chassis

Discussion in 'URGENT - Help Quick!' started by akbaanwar, May 13, 2017.

  1. akbaanwar

    akbaanwar Member

    Posts:
    7
    Likes Received:
    0
    Joined:
    May 13, 2017
    Location:
    Pakistan
    hi,

    Guys i've bought AT engine wiring harness(reason for buying AT harness is because i didn't found MT chassis in the junkYard) for 98 accord MT chassis, i need to know detailed pinouts for the 10pin plug c102.

    It's urgent please help!!
     
  2. dawg316

    dawg316 Well-Known Member

    Posts:
    180
    Likes Received:
    0
    Joined:
    Dec 25, 2016
    Location:
    canada
    what engine the v6 or the f23 vtec.

    need a pic of the auto harness or manual harness connector c102

    also a highlighted pic of where connector c102 is would help too

    you have to provide all the info you can if your asking for detailed help.
     
  3. akbaanwar

    akbaanwar Member

    Posts:
    7
    Likes Received:
    0
    Joined:
    May 13, 2017
    Location:
    Pakistan
    Below is the picture i got from this website while i was searching for my issue,
    the first left top AT 14pin plug is what came with the harness i brought.
    and the last right bottom 10pin male connector is in the MT chassis.

    i have to remove all AT wires from the harness and add vss and Backup wires, so to do that i'm confused on MT chassis wiring.


    By the way i've seen your youtube channel, you've clean accord ! :waytogo:
     
    Last edited: May 13, 2017
  4. dawg316

    dawg316 Well-Known Member

    Posts:
    180
    Likes Received:
    0
    Joined:
    Dec 25, 2016
    Location:
    canada
    forgot to add the picture. suns gonna go down here so i can get you a pic and labeling from my chasis tomorrow or maybe today
     
  5. akbaanwar

    akbaanwar Member

    Posts:
    7
    Likes Received:
    0
    Joined:
    May 13, 2017
    Location:
    Pakistan
    i couldn't able to upload pic even after keeping the pic format in website specs,
    try the link below for the picture,

    drive.google.com/open?id=0Bz8Rn6nGVzA-bElDblB6MXpqUlk

    98 accord H22a with obd1 to obd2b conversion harness, old engine wiring was burnt according to the owner of the car,
    chassis is MT with c101 and c102 shock tower connectors, i got the engine harness from AT accord where i have to add VSS and Reverse wirings , so i need to know exactly detailed pinout on c102 10pin connector.

    Thanks
     
  6. dawg316

    dawg316 Well-Known Member

    Posts:
    180
    Likes Received:
    0
    Joined:
    Dec 25, 2016
    Location:
    canada
    My car doant have that connector gguess cuz its north american model

    The pic you posted is a detailed pinout tho. Aslong as the wires connect back to the right ecu pinout it will work
     
  7. akbaanwar

    akbaanwar Member

    Posts:
    7
    Likes Received:
    0
    Joined:
    May 13, 2017
    Location:
    Pakistan
    MT c102 10pin

    The yellow wire in c102 and grn/blk backup wire, will both gonna run to the reverse switch ?

    And the pin 2 grn/blk circuit z28 <--- i don't have z28 diagram what's this where it'll go??
     
  8. akbaanwar

    akbaanwar Member

    Posts:
    7
    Likes Received:
    0
    Joined:
    May 13, 2017
    Location:
    Pakistan
    For the VSS center is signal and others are yel/blk and grd so from the back of connector yel/blk is on right or left ?
     
  9. dawg316

    dawg316 Well-Known Member

    Posts:
    180
    Likes Received:
    0
    Joined:
    Dec 25, 2016
    Location:
    canada
    reverse light harness = 2 wire. power in and reverse light out
    power in is yellow 12 volts.
    reverse light out is green/black

    you also need a pinout for vss?
     
  10. akbaanwar

    akbaanwar Member

    Posts:
    7
    Likes Received:
    0
    Joined:
    May 13, 2017
    Location:
    Pakistan
    No, I got it for vss,

    Thanks alot bro
     

Share This Page