Recent content by persain48820

  1. persain48820

    My H22a4 build (FINALLY GETTING STARTED!)

    I did in fact to that. Since I will have to pull everything back apart, it will be cleaned off! Thanks for the input!
  2. persain48820

    My H22a4 build (FINALLY GETTING STARTED!)

    Well on this humid, muggy evening in Bowling Green, KY, I finally got started on the building of my h22, finally! After waiting on parts and botching the order of my 55mm ACL race main bearing, I finally got some OEM 50mm replacements. So tonight, I got started on putting the bottom end...
  3. persain48820

    Plz help!! Main bearing won't fit flush!?

    I do remember specifically telling FRSport.com I needed them for a H22a4. The block is from a 97. I ran the model number on the box 5M1957H-STD, and it pulled them up for a H22a4: http://www.aclperformance.com.au/us/...Bearingsus.htm It seems that they are 55mm and not 50mm...
  4. persain48820

    Plz help!! Main bearing won't fit flush!?

    Starting the assembly on my h22 and my ACL main bearings won't fit. I flush the notch with the bearing in the grove of the bearing journal and the opposite side is about a 1/2 inch above the other side. If anyone has any insight, please let me know something!
  5. persain48820

    FINALLY!!! My basement just got really messy!

    Nice buy! I thought I did good to pay $400 for mine but now I feel like I got raped lol! Good luck with the build though! I too am about to start putting mine back together once I receive my ACL rod and main bearing and front and rear main seals sometime this week. Hopefully I haven't gotten...
  6. persain48820

    Finally got my H22

    yea i pretty much lucked out. his dad told him to get it out of his garage so i was very happy to take it off his hands!! have almost everything i need except a wiring harness so if anyone knows where i can find one for the h22a4 please let me know!! thanks
  7. persain48820

    Finally got my H22

    So I finally picked up my motor last night for a staggering $400, DEAL! Supposedly it has been bored .020 and has Type S pistons, but the number on the piston is P5M and not P5P so this has led me to believe the guy I got it from doesn't know what he's talking about. So I talked to him about...
  8. persain48820

    Required ECU for swap

    Ok, so, tomorrow I'm going to pick up my USDM H22a4 out of a 97 lude. Found a wiring harness out of a 01 for it, now I just need the ecu. Wanting to stay OBD2 for the time being so what ecu would I need? I know I need one out of a 96-01 but what ecu code am I looking for? I've done my...
  9. persain48820

    H22a4 Manual Wiring Harness/ECU

    Buying a H22a4 this week to put in my 01 accord and it does not have the wiring harness or ecu so I need both if possible.
  10. persain48820

    H22 or F20b... Which is easier?

    Ah I see. I had planned on using hondata.
  11. persain48820

    H22 or F20b... Which is easier?

    As far as wiring goes, which one is a little less complicated?
  12. persain48820

    H22 or F20b... Which is easier?

    With tax returns on the horizon, I finally plan to swap my F23 for a H22 or F20b. I'm ok with using either engine, I just want to know which is an easier to swap. I've done some research into doing the swap but haven't really found which is easier, granted a engine swap is not easy. Any help...
  13. persain48820

    throwout bearing

    ok so im pretty sure the throwout bearing in my car is going out. while im accelerating in gear or at a constant speed i hear a roaring kinda like the noise you would hear out of a rear end. when i coast in or out of gear the noise goes aweay. i have done some research and asked some of my...
  14. persain48820

    OFFICIAL...WHITE coupe/sedan crew ROLL CALL

    my white 2dr
  15. persain48820

    Front 6.5" Speaker installation (doors)

    great post. i put alpine type r 6.5's in and they were too deep. they were a full inch taller than the stock speaker. me and my friend put them in used some 3/4 inch ply wood to make a spacer and we figured out how to use the stock mounting points of the stock speaker.
See more

Latest posts

Random media

stock right now besides a SRI, and the icw wheels that came on it. Just ordered sensen struts and egay sleeves (soon to be gc sleeves)
DSC00762a
engine angle view (after cleaning)
12696360 1036378873090205 1362490844 o 2/7/15
Purple cluster
Back
Top