What'd you do to your accord today?

[RedRyder]

Went to buy a replacement air filter and wound up with aluminum racing pedals instead. Oops.

 

[xci.ed6]

I was bored...I had a set of old pedals, manual trans, but I have an auto? Oh well, they fit, it goes will with my new shifter

Which is a Honda Prelude shifter, fit in my Accord with a few washers, and the console pulled, covered with a shifter boot with a bracket from an I4/MT car, with a pool ball I drilled and tapped M14 so it all fits like glove

-I did do it a bit ago, don't think I showed the pedals-

 

[Teesak]

I was bored...I had a set of old pedals, manual trans, but I have an auto? Oh well, they fit, it goes will with my new shifter grin

Which is a Honda Prelude shifter, fit in my Accord with a few washers, and the console pulled, covered with a shifter boot with a bracket from an I4/MT car, with a pool ball I drilled and tapped M14 so it all fits like glove

-I did do it a bit ago, don't think I showed the pedals-

That shift knob is dope and the fact you made it makes it that much cooler. props on the mod

 

[james'99]

Received the non-6GA factory mufflers today!! They're together with the Y-pipe, built-in as a whole piece, unlike 6gen's.

So far, the plan is to chop off the Y-pipe, and get a custom stainless steel Y-pipe, but...

Although this Y-pipe is a mild steel, which it will eventually rust but, it looks pretty damn good as is.. I might keep it as is, and have the shop custom weld it.

Gonna go to the shop w/ the mufflers tomorrow, and talk to the guys to see what would be the best for me.

Can't wait to see what comes of this Rich!

Went to buy a replacement air filter and wound up with aluminum racing pedals instead. Oops.

Works for me!

Nice use of the pedals xci! Really original and you actually made it functional which is awesome!

 

[DizzyP]

Clamped the springs to lower it. Only like an inch or two, still playing with it. The stock set up looking like it had a lift kit all these years finally got to me.


iPhone using Tapatalk, sent from my.

 

[Sil2DrV6]

Received the non-6GA factory mufflers today!! They're together with the Y-pipe, built-in as a whole piece, unlike 6gen's.

So far, the plan is to chop off the Y-pipe, and get a custom stainless steel Y-pipe, but...

Although this Y-pipe is a mild steel, which it will eventually rust but, it looks pretty damn good as is.. I might keep it as is, and have the shop custom weld it.

Gonna go to the shop w/ the mufflers tomorrow, and talk to the guys to see what would be the best for me.

Can't wait to see what comes of this Rich!

It will be done next week!

__________________


Went to the shop 'n talked to the guys. The built-in Y-pipe will stay w/ the mufflers. Even if it's mild steel, it will take years 'n years for it to be rusted. And I can clean it pretty good b/c I'm an OCD. Lol

 

[agginline86]

finally bought fogs for the coupe!
amazon had them for $140

 

[Varnell]

Blew my front driver's side component speaker/tweeter. They lasted a good two and a half years with a 1800w Kenwood amp fueling the audio. Shifted the audio position from F2 to R2. Who has money to spend on speakers these days? lol

 

[DizzyP]

Clamped driver side front spring. Haven't had a chance to see how it looks since I was in a rush to get it done. I'm not gonna name any names but someone loosened the lug nut but didn't tighten em up and I almost lost my wheel on the freeway. I was able to tighten which em up on the freeway and feel nice.


iPhone using Tapatalk, sent from my.

 

[Sil2DrV6]

Did the ultra super subtle cosmetic work on my front-end today.