Search results

  1. A

    black housing headlights?

    ^ This. I have Nokyas in my DRL/high beam housing, and the yellow reflection off the buckets is enough for me. Will try and get a pic.
  2. A

    Flex Pipe Diameter?

    Hi guys, I'm having trouble finding this info online. I want to replace my leaking flex pipe with a standard piece I can get locally for cheap instead of ordering and shipping in the larger complete flex pipe with flanges. I can't find the diameter anywhere online though. I can't get my...
  3. A

    Why the heck is it so hard...

    Got a set here as well - sorry if it seems like we're rubbing it in :Boo: As far as I know, Nissan Sentras and S13s share our bolt pattern (assuming the 4x114.3 bolt pattern is what's holding you back). Good luck!
  4. A

    Problem: Re-Installing Transmission Mount

    Hi guys, Here's the bad boy I'm working on. My 2001 5-speed: I replaced the driver's side motor mount without a problem. After some disassembly, it appears I can't replace the transmission mount without dropping the trans, something I'm not equipped to do right now. Now I'm...
  5. A

    Cg3 5spd rpm hanging

    I second cleaning the throttle body. Also, what do you consider high idle? When my car is cold it idles around 1500-1600 rpm.
  6. A

    6spd for 4 cylinder

    Why not replace the synchro then?
  7. A

    Tire size/brand recommendations?

    195/65/15 is the factory size to the best of my knowledge. A 205/65 will have a larger outer diameter, and may confuse the wheel speed sensors/ABS. Considering the low mileage on your other tires, I would only two with the same brand and size tires as on the front.
  8. A

    DIY: Rear Wheel Bearing Replacement

    Thank you for this DIY - I'm finding it very helpful as I swap a rear wheel bearing/hub on my car. I ran into the same problem OP did where the race decided not to come out with the rest of the hub - I don't have a dremel, and there isn't an electrical outlet in my apartment's underground...
  9. A

    How many miles does your accord have?

    If it doesn't need a new engine, don't put one in. Especially if you're trying to sell it. The merits of a used car with a different engine are questionable, at best. To me, the majority of the time a car with a non-original engine means that the first engine wasn't maintained appropriately.
  10. A

    Replacing coilovers - FF2 or koni yellow?

    Koni Yellows are rebuildable - if you can get the sleeves unseized, that may be the most cost-effective way to go while still remaining with a good quality suspension.
  11. A

    Aman's 2001 5MT

    Well, I think my car is just interesting enough to have its own thread. I won't call it a build, since I really don't have an end goal or a particular list of things I want to do. I'm going to try my best to put things in chronological order. I bought the car in November of 2014...
  12. A

    Brake Line leaking

    Do the brake lines start down at the bottom of the driver's side strut tower?
  13. A

    Clutch Slave Cylinder Replacement - Mishap

    Last question, I promise: This is how the clutch slave cylinder/clutch fork look when the clutch pedal isn't depressed. Does this mean I need a new clutch? That's what my mechanic said. That boot should be completely snug when the clutch is engaged/pedal not depressed. Just looking for a...
  14. A

    Clutch Slave Cylinder Replacement - Mishap

    Welp, this car seems eager to prevent me from fixing it. My current challenge is with part #3 in the picture below. The clip holding the master cylinder to the clutch hard line: Taking it out was a nightmare. Reinstalling it is like something out of a Stephen King novel. How did you...
  15. A

    My 2001 EX Coupe

    Interested to see results! Another option too is to maybe put it in the bend itself - the straight portion between the two bends? Maybe it'll fit?
  16. A

    Clutch Slave Cylinder Replacement - Mishap

    Thanks for the pic. The #20 parts are what I was talking about. I ended up getting those off and pulled out the old line. The new line I rerouted behind the intake manifold, along the top of the firewall. Everything is finally installed, hopefully going to bleed it tomorrow and have it...
  17. A

    Clutch Slave Cylinder Replacement - Mishap

    Update: I ended up finding a guy parting out a 2000 Accord. Got the master, line, and slave for $50. :) I'm in the process of installing it now. Got almost everything undone except for the retainer holding the clutch line to the firewall. Anyone have experience with that part?
  18. A

    Clutch Slave Cylinder Replacement - Mishap

    Thanks for the search! I think that eBay ad is just for the master and slave cylinders. It says the clutch hose may be needed, at a cost of $147.90. I think I'm going to expand my search for these cars at junkyards.
  19. A

    Clutch Slave Cylinder Replacement - Mishap

    Hi folks, I was hoping for a little bit of advice/alternate ideas to the pickle I'm currently in. While removing the clutch slave cylinder on my 2001 sedan, I made a mistake. I turned the fitting attached to the clutch line, instead of the actual fitting between the slave and line. The...
  20. A

    PuzzleMaster94's J32 6MT 1999 Accord EX-L V6 Coupe (56k)

    Re: PuzzleMaster94's 1999 Accord EX-L V6 Coupe (56k) *Rotiform Content* Looks good! A friend of mine tagged me in one of your shared pictures on Instagram, told me to make my car look like yours haha.
  21. A

    straight pipe for the 4cyl

    ^ I'm interested to hear what your exhaust diameter is as well. Also, how does that O2 spacer fit? I'm thinking of getting one myself (cat is out), as a temporary CEL satisfier.
  22. A

    What'd you do to your accord today?

    I installed my $68 clutch slave cylinder yesterday, breaking the $200 clutch line in the process. :shakehead: Gonna go to some junkyards tomorrow to see if I can source a good line for... well, a little less.
  23. A

    Sino's 1999 Accord EX Sedan 5MT (56k)

    Good read!
  24. A

    ickna11's [H23A] VTEC [5MT] Swapped EX-L 2k Coupe (12/23/16)

    Re: ickna11's [H23A] VTEC [5MT] Swapped EX-L 2k Coupe Congrats!
  25. A

    My 2001 EX Coupe

    I was wrong on the location, it seems to be in the same place as yours. Mine is the factory resonator. This pic is from behind the passenger side rear of the car. You can see the resonator in front of what looks to be the rear subframe. It looks like an oval/slot kind of shape. Your pic is...

Latest posts

Random media

image
rsx
New rims 2
3201.jpg
Great Eddy EvoII
Back
Top