Recent content by derpson

  1. derpson

    H22 Header

    Basically there were two great headers ever offered for an H22. A HYTECH, and the MUGEN. That being said you can source an HYTECH rep through the Preludepower.com group buy, the Mugen is a unicorn. The Vibrant header is readily available, and also an excellent option. The third option is to...
  2. derpson

    Wheel Fitment Thread

    Never got a chance to shoot my car but here are some crappy cell pics for end of year . H2Oi: Random again at H20i Back in 4X4 mode now. Hopefully this car makes it to next summer.
  3. derpson

    Wheel Fitment Thread

    What? Pinch welds beaten with a hammer primed, and resprayed. First drive was good as far as clearance and rubbing issues. Still have some braking issues to chase.
  4. derpson

    Wheel Fitment Thread

    Well after bike fest, then that random tornado, and a whole bunch of BS that led to an 80 hour work week I finally got my car on the lift today. I beat that damn pinch weld with a ball peen hammer. I might finish it with the roller tomorrow even though I already re painted it. I also had...
  5. derpson

    *Slammed Thread* (56k)

    My friend Nick's GTI we did a ACCUAIR controller setup, 2x Viair compressors, all the work done in my shop. He is the first and only owner of this car. We still have to notch the front for the control arms. The rear has been notched since this pic.
  6. derpson

    Wheel Fitment Thread

    Thank you so much! :omgbd: Since I have to take the wheels off again this will be simple and save me from possible epic failure!
  7. derpson

    Wheel Fitment Thread

    Nope. I Ran into a random problem with the braking system, and it's still at my shop I may snap a cell pic of it covered in dirt though. If I do I will post it. If not I am off to Bike weekend in Carlisle so I probably won't work on it again till Sunday or Monday. Then maybe I can get some more...
  8. derpson

    99CcordMTF23's H22-Swap thread! Update, 10/26/12, pics pg6! RUNNING!

    Re: 99CcordMTF23's H22-Swap thread! Small Update, 6/28/12, pics pg6! RUNNING! WOW! That's a rat's nest, and a half. The beer is cool but the but connectors and such tend to cause problems later down the road. I assume you are going to use a stock Honda coil?
  9. derpson

    Wheel Fitment Thread

    ALLGOnoSHOW thanks! It's up about 1.5"in the rear and 1.75" in the front. Still tucking tire but I can turn now. Has anyone ever had a problem with the pinch weld on the front upper frame rail coming into contact with the tire??? I know a lot of people are running a similar setup, and I don't...
  10. derpson

    Wheel Fitment Thread

    Thank you much. It does look sick, but honestly I can get about 170 degrees of steering wheel turn before I rub. I will probably have to go up about an inch, to an inch in a half in the front. Maybe about a quarter to a half in the rear. For reference this is F2 T2 coilovers. Front is bottomed...
  11. derpson

    Wheel Fitment Thread

    TSW Nurburgrings 18X9 +32, 225/40. Still need to clearance the rear bumper more and put the front up. I had to roll the front tabs, and remove the inner fender to get it this low. No camber kit in the front, megan in the back.
  12. derpson

    Wheel Fitment Thread

    Ok I got some work done this weekend.
  13. derpson

    Wheel Fitment Thread

    Shadow1, Sleeper cell thank you for the pertinent answers. I think I am just going to put the rear on, obviously get it aligned, and be done with it. If it doesn't drive to my liking, or my tire wear is obnoxious, and I believe that front camber plays a role I will install the kit. For now it's...
  14. derpson

    Wheel Fitment Thread

    Really no front camber kit??? I have one in my Prelude and the strut towers are getting tore up. How do your front tires wear, and would you suggest rotating them to the rear often if the rear has a camber kit? On another note Picked up the goods from my friend today. Can't even tell...
  15. derpson

    Wheel Fitment Thread

    Haven't posted in a while,....but just dropped my rims and tires off at my friend's shop. Apparently he has one of those "touch-less" tire machines??!!?? Either way my rim protector broke, and I am waiting for a new one. The last piece of the puzzle showed up a couple days ago too...Lug nuts. I...
See more

Latest posts

Random media

3520.jpg
IMAG0334
Car flat black, oem wheels, yokhama tires, oem foglights yellow bulbs, halo headlights 6000k hid, oem tail lights, 3" catback (custom), DC headers, ae
image
3805.jpg
Back
Top