00Accord4cyl
The Orange Skittle
either of you have some cutoff pics?
Retrofit Club
- Thread starter angelplus
- Start date
av6_sm1ke
Well-Known Member
My rotation is a bit off, but I'll snap a few. I'm hungry so I'll grab some food while I'm out 
Be back in 30
Be back in 30
finch13
Well-Known Member
My rotation is off as well, I must have levels them on an unlevel surface.
Low beams (I know my alignment is off, I didn't trim enough so they're eternally adjusted like / \, but it's hardly noticeable on the road):
Bixenon + stock high beams:
Low beams (I know my alignment is off, I didn't trim enough so they're eternally adjusted like / \, but it's hardly noticeable on the road):
Bixenon + stock high beams:
av6_sm1ke
Well-Known Member
Here are my cutoff pics.. I just tossed my projectors into my headlights without doing any mods to them because I didn't have time.
First, a shot of my old HID setup. Prolumens 9006 PnP kit with 35w ballasts and 6000k bulbs (Keep in mind that these headlights also have eyelids, which eliminate a LOT of glare, and I've also aimed them lower to reduce glare to oncoming drivers):
New setup: Morimoto H1 Bi-Xenon projectors, Morimoto 35w ballasts, and 5000k Morimoto H1 bulbs. I also got a pair of CCFL rings, but I broke both of them during the installation/aiming of the headlights
Actual cutoff (same distance as first pic with pnp kit)
And a pic to show the actual distance from the wall:
If anyone is considering an entry level projector retrofit, the Morimoto H1s are the best all around option. On top of that, the service I received from the guys at TRS.com was amazing, hands down one of the best vendors I have dealt with online. You just can't lose with this setup!
First, a shot of my old HID setup. Prolumens 9006 PnP kit with 35w ballasts and 6000k bulbs (Keep in mind that these headlights also have eyelids, which eliminate a LOT of glare, and I've also aimed them lower to reduce glare to oncoming drivers):
New setup: Morimoto H1 Bi-Xenon projectors, Morimoto 35w ballasts, and 5000k Morimoto H1 bulbs. I also got a pair of CCFL rings, but I broke both of them during the installation/aiming of the headlights
Actual cutoff (same distance as first pic with pnp kit)
And a pic to show the actual distance from the wall:
If anyone is considering an entry level projector retrofit, the Morimoto H1s are the best all around option. On top of that, the service I received from the guys at TRS.com was amazing, hands down one of the best vendors I have dealt with online. You just can't lose with this setup!
acedomain
Well-Known Member
wow i cant wait to do my setup ....im gonna use the morimoto h1s for my high beam retros and with the cut off pics you put up i feel much better about using them.....
So what about your low beams lolwow i cant wait to do my setup ....im gonna use the morimoto h1s for my high beam retros and with the cut off pics you put up i feel much better about using them.....
SykVSyx
Well-Known Member
How much did those Morimoto projectors run you guys?
acedomain
Well-Known Member
for my low beam i have some tsx projectors that are overdue to get retrofitted....i didnt want to thread jack and explain my setup just wanted to mention that his pictures did justice.....
they are like 90 to 120 on trs......but i think that guy ''shavedaccord'' or something got is for less would ask him......here is the link http://www.theretrofitsource.com/pr...d=221&osCsid=7eebff102d00dd8e436277469410c06b
SykVSyx
Well-Known Member
Appreciate the link, thanks.
I'll talk to Darryl as well and see what info he has as well.
I'll talk to Darryl as well and see what info he has as well.
