Search results

  1. O

    Timing belt??? Please advise..

    Doing mine tomorrow at 171,360 miles and I drive the s#!t out of my car! Never been done before.... I got REALLY lucky!
  2. O

    Wheel bearing replacement?

    Same thing happened to me two years ago. Like said before, they do have to be pressed out and back in. I have heard of people using a heavy hammer and a peice of wood to beat them out and then back in, but they are in there TIGHT! It would take a lot of banging and that can't be good for the...
  3. O

    Another TrimBrite Project

    Not too shabby! Hell, I might try this myself... I have the same problem. As far as the rust goes... by the time it rusts through I might have the funds for a CF hood.
  4. O

    Help With a Carseat.

    I went to the local police station to have my son's carseat properly installed. The officer said that just using the seat belt through the back was enough. Just pull the belt all the way out till it clicks, feed through the back of the seat, buckle it and cinch it down with all of your...
  5. O

    Timing Belt Kit?

    I feel ya buddy! I've got two kids and go to school full time. A lot of people on here have a steady income and apparently a lot of free time. I don't see anything wrong with buying parts off of ebay, as long as they are quality parts. It looks to me like the parts in that auction are...
  6. O

    *MASSIVE* Mid-Missouri Meet 6/4/2011

    Nice! Thanks for the pointers :eusa_wall:
  7. O

    Replace Mount When Rebuilding Transmission?

    Yeah... Thats why I waited so long... $ Do yourself a favor and have all of them checked out cause it is a chain reaction... one goes bad and it stresses another and so on...
  8. O

    Replace Mount When Rebuilding Transmission?

    I drove my V6 coupe for a couple of months with the trans slipping. A few weeks after I had the tranny rebuilt I started noticing the engine "jumping" or making a loud clunk noise when I would put it into gear or accelerate hard. The tranny slipping for those couple of months had broken my...
  9. O

    *MASSIVE* Mid-Missouri Meet 6/4/2011

    Sounds good.
  10. O

    Any Others with the DC Sports 4-2-1 Header

    It did to mine but it also made for a rough idle and threw an engine code
  11. O

    You might be "too low" if...

    My SLR was stolen out of my car last December. Still haven't replaced it and that was my only camera except for my POS phone camera. As soon as I get a new camera I'll put up pics.
  12. O

    You might be "too low" if...

    I'm still playin with the height. I may go back down 1/2 inch or so... not sure. You gotta compromise when your daily driver can't be daily driven anymore.
  13. O

    You might be "too low" if...

    Lol... That happened to me with a trash can lid in my garage. My car smelled like melted plastic for weeks every time I drove it.
  14. O

    You might be "too low" if...

    Noob? Ha! I've been driving this car for eight years lowered 2.5+ inches. Just decided to go to the flo... just ended up being too much for the daily things I do. Did anybody actually read the initial post to the end where it says, "Anyone realize they were too low and have a good story...
  15. O

    You might be "too low" if...

    Yeah... the car wash probably wasn't the smartest move, but there was no way around the speed bump. Had to pick up my son and it spreads the whole width of the pick up line... can't even get into the frickin parking lot without going over one!
  16. O

    You might be "too low" if...

    I used to be that way until I found this place. Car comes out looking pristine and it takes 5 minutes instead of the 30 I used to take when I would do it myself. Plus if its good enough for the hundreds of Mercs, BMWs, and Lexus's that go through there everyday, its good enough for my Accord.
  17. O

    You might be "too low" if...

    ... you get stuck in an automatic car wash and get high-centered on a speed bump all in one day! Hey guys, I just recently slammed my coupe on F2 type 1's. Never really though about it but being slammed is really freakin inconvenient! Went to the car wash the other day (one of those big...
  18. O

    Another twin turbo Accord/Inspire?

    Wow! I'm at a loss for words! :thinking:
  19. O

    *MASSIVE* Mid-Missouri Meet 6/4/2011

    Oh yeah I know where Lawrence is!!! Had many friends at KU... been there many times. Crazy town! Plus my family has a farm in Eudora, right outside of Lawrence
  20. O

    *MASSIVE* Mid-Missouri Meet 6/4/2011

    I'll probably join you guys. Lets talk when it gets closer and see if we can meet in KC and go down together. Are there any other members in KC? I see moded 6GA's all over KC but don't see them on here.
  21. O

    *MASSIVE* Mid-Missouri Meet 6/4/2011

    It all depends on if I get all my **** together by then. I've got a pretty clean ride but right now its in pieces and looks like crap. Rather not go to a meet unless its in tip top shape... know what I mean?
  22. O

    *MASSIVE* Mid-Missouri Meet 6/4/2011

    I live in Overland Park. I just got my new 02 front bumper painted and I'm trying to decide what front lip will go best with my oem sides and rear. Hopefully I can get it all together and mounted and get new tires before the meet. Need to get some pics up on here too. There aren't many...
  23. O

    my car is in a random video!!!!!!!!!!!

    Ha! :fail: My bad! Video is so dark it looked black.
  24. O

    what do yall think?

    Who puts forth the effort to convert to a Prelude rear end!?! I've seen a skyline rear end conversion that looked pretty sick... this... not so much! Just my opinion.
  25. O

    Throttle "stutter" @ 4000 RPMs

    Hard acceleration or normal? While turning or going straight? If its while turning or hard acceleration, I'd say check your oil level.

Latest posts

Random media

81.jpg
20130907 163315
622
DSC04260
Magnaflow Cat Back
Back
Top