Any part for 5 speed swap

[kashmeister]

Parts purchased:

2000 60675mi Manual Transmission (with speed sensor/reverse gear sensor)
98-02 Accord Shifter Assembly
98-02 Accord Shift Cables
Fidanza Short Shifter
Type R Shift Knob
JDM Shift Boot
93 Accord Clutch Master Cylinder
93 Accord Clutch Reservoir tank
93 Accord Clutch Line
93 Accord Clutch Dampener
98-02 F1 Racing Chromoly Flywheel
98-02 Exedy OEM Clutch Disc + Pressure Plate
90-93 Stainless steel line (hard line --> this --> slave cyl)
98-02 Manual Starter
98-02 Clutch slave cylinder
98-02 Clutch Master Cylinder
98-02 Drivers Side CV Axle
98-02 Halfshaft
98-02 Gas + brake Pedals
00 EX ECU
Mobil1 synthetic + purolator filter
wheel bearing grease for axles and stuff

Tranny Mounting Misc Parts:
3x Tranny mount to firewall bolt: 95701-12025-08 (If it doesn't come with the one I bought)
1x Tranny mount through bolt: 95801-12125-08

Drivetrain Misc Parts:
2x Halfshaft hex bolt: 90102-SF1-000
1x Halfshaft Bolt: 90165-SE0-000

Shifter Assembly Misc Parts:
1x Select Cable Linkage Pin: 54116-SV4-000
1x Select Cable Split Pin: 94201-20350 or 94201-20220
1x Shifter Nut: 90114-SA0-000
1x Shifter Washer 90551-SV4-000
2x Shift Cable Bracket Bolt: 93402-06012-08

Starter Misc Parts
1x Long Starter Bolt: 95701-12105-08

Clutch/Flywheel Misc Parts:
8x Flywheel Bolts: 90011-PH3-000
6x Pressure Plate Bolts: 90034-P10-A01

Clutch Line Misc Parts:
1x Master Cylinder Clip: 46924-S84-A02
1x Master Cylinder Lock Pin: 46911-S70-003

Clutch Housing Misc Parts:
1x Dowel Pin: 94301-14200

General Misc:
1x Clutch Fork/Shift cable/slave cyl **** urea grease: 08798-9002
2x Oil pan/tranny crush washer: 94109-14000
1x Trunk Latch: 74862-S84-A01
1x Valve Cover Bolt: 90013-P0A-000
1x Valve Cover Bolt Washer: 90442-P0A-000


_________________________________________________________________________________________________________________________________
_______________________________________________________________________________________________________

NOTES TO SELF
-Thick Washers for Master Cylinder

Power Steering Fluid
Brake Fluid
Honda MTF (wtf is the part number?)
1/4" tubing to fill tranny




ball joint fork

 

[BadgerType]

http://www.6thgenaccord.com/forums/showthread.php?t=32598

i can also get parts for ya from a local junkyard on fridays

 

[kashmeister]

http://www.6thgenaccord.com/forums/showthread.php?t=32598

i can also get parts for ya from a local junkyard on fridays

that would be sweet... do they have a good donor car?

also I saw that you had the shifter assembly, can you hold it for me until you check the junkyard so you can just ship everything at once?

 

[BadgerType]

its not that kind of junkyard, i pull the parts from cars that have compatable parts

 

[kashmeister]

its not that kind of junkyard, i pull the parts from cars that have compatable parts

Alright badger, any part i need that you can get at a reasonable price.

the junkyards around here only mainly have american cars but I am in contact with someone at a yard i found 30mins away called "Bionic Auto Parts"

The guy said that they have a few MT 6GA and he can give me a nice deal if i give him the list of what i need and he pieces it for me. They have 3 trannys listed on their site, one from a 2000 with 87k for $325

I'm going to call them up tomorrow and I don't have school Thurs/Friday so I can check them out. Dude had a sketchy email though, it was like [email protected] or something.

 

[Hondastylez]

Look here.
http://www.6thgenaccord.com/forums/showthread.php?t=33158

 

[kashmeister]

Look here.
http://www.6thgenaccord.com/forums/showthread.php?t=33158

$100+ship is steep.... I'm going to check out yard first

 

[Hondastylez]

$100+ship is steep.... I'm going to check out yard first

Don't be afraid to shoot me an offer.

 

[kashmeister]

Don't be afraid to shoot me an offer.

I'll keep you in mind if I can't get it at the junkyard

 

[BadgerType]

ehh, i could get most parts but i wont get you a tranny. everything else, yes. trannys are a hassle and seeing how far i have to carry that ***** around and shipping it via pallet is not my cup o tea

but yeah, shoot me a list of whatcha need and i will send ya an estimate of the cost shipped to you.